LIMITED WARRANTY
PerTronix, Inc. warrants to the original purchaser of its products that the
Ignitor III shall be free from defects in material and workmanship for a period of
(30) months from the date of purchase.
If within the period of the foregoing warranty Pertronix finds, after inspec-
tion, that the product or any component thereof is defective, Pertronix will, at its
option, repair such products or component or replace them with identical or simi-
lar parts PROVIDED that within such period Purchaser:
Promptly Notifies Pertonix, in writing, of such defects.1.
Delivers the defective products product or component to Pertronix (ATTN: 2.
Warranty) with proof of purchase date; and
Has installed and used the product in a normal and Proper manner, consis-3.
tent with Pertronix printed instructions.
THE FORGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING
AND IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A
PURPOSE.
THE FURNISHING OF A REPAIR OR REPLACEMENT COMPONENTS SHALL
CONSTITUTE THE SOLE REMEDY OF PURCHASER AND THE SOLE LIABILITY
OF PerTronix WHETHER ON WARRANTY, CONTRACT
OR FOR NEGLIGENCE,
AND IN NO EVENT WILL PerTronix BE LIABLE FOR MONEY DAMAGES
WHETHER DIRECT OR CONSEQUENTIAL.
PRIOR TO INSTALLATION TURN IGNITION SWITCH OFF
OR DISCONNECT THE BATTERY
12-VOLT NEGATIVE GROUND INSTRUCTIONS
GENERAL INFORMATION
See our website (www.pertronix.com) for the latest product information. 1.
IMPORTANT: Read all instructions before starting installation.
WARNING!!! DO NOT USE WITH SOLID CORE IGNITION WIRES. 2.
The Ignitor III may not be compatible as a trigger for other electronic boxes.3.
The Ignitor III Rev-Limiter is preset at 5500 RPM’s. The Rev-Limiter can be user set 4.
to a minimum 4000 and a maximum 9000 RPM’s.
All external resistors must be removed to achieve optimum performance from the 5.
Ignitor III ignition system.
440 East Arrow Highway
San Dimas, CA 91773
909-599-5955
www.pertronix.com
IGNITOR III INSTALLATION
Note: A magnet sleeve is not required and the air gap between the face of the
module and the cam is not adjustable.
Remove cap and rotor from distributor. Do not disconnect spark plug wires from cap.1.
Examine cap and rotor for wear or damage. Replace as needed.2.
Disconnect the points wire from the (-) terminal of the Ignition coil.3.
Remove clip from vacuum advance arm. Remove vacuum advance screws and 4.
remove vacuum advance completely from distributor.
Remove breaker plate screws and lift out entire breaker plate assembly.5.
The Ignitor III does not require any modification to the distributor. Therefore the 6.
breaker plate, breaker points, condenser and hardware can be used as backup.
Clean all dirt and excess oil from the point cam.7.
Ignitor III assembly Installation: 8.
Install Ignitor III assembly onto distributor. •
Line up base plate assembly screw holes to distributor housing. • NOTE: Module
assembly screw holes will only line up one way.
Rotate module assembly top plate to clear mounting screw holes. • (See Figure 1)
Install provided 8/32 flathead screw into counter sunk hole on module assembly •
bottom plate, do not tighten. NOTE: 8/32 flathead screw must be installed in the
counter sunk hole.
Insert provided ground wire end onto provided 8/32 pan head screw, install screw •
and ground wire onto bottom plate and tighten both screws evenly.
Install vacuum advance onto distributor, secure vacuum advance arm with original •
or provided clip. Secure vacuum advance with original screws. TIP: Install vacuum
advance arm to Ignitor III adapter plate pin first before tightening screws.
For complete installation see figure 2.•
For Part Number: 71281
04-09 0000-003004
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern