Pertronix JBA Exhaust 40-3114 Bedienungsanleitung PDF herunterladen

INSTALLATION INSTRUCTIONS

** Installation recommendation: JBA recommends in most case that the vehicle be taken to a reputable exhaust shop for installation.

JBA recommends taking the vehicle to a mufer shop and having all slip connections tack welded. 12.09

40-3113 & 40-3114

2010 Chevrolet Camaro SS 6.2L - 3 inch system

Parts List Qty.

A. H Pipe Assembly Driver side 1

B. H Pipe Assembly Passenger side 1

C. Driver side Intermediate Pipe 1

D. Passenger side Intermediate Pipe 1

E. Driver side Mufer Assembly 1

F. Passenger side Mufer Assembly 1

G. Sure Seal™ clamp 4

H. U-bolt clamp 1

I. Sure Seal™ clamp (40-3113 Only) 2

Recommended Tools:

15mm deep socket

9/16 deep socket

13mm deep socket

Small at head screwdriver

Pliers

Pry bar

WD-40 or equivalent

Start:

1. Remove and inventory new JBA

exhaust system.

2. Disconnect negative battery

cable and allow vehicle to cool.

3. With the vehicle raised and

properly supported, unbolt the fac-

tory cross member that runs under

the drive shaft and swing it out of

the way.

17. Check all clamps and con-

nections for proper t and align-

ment. Double check all clamps are

tightened and that all hangers are

secure in rubber grommets. It is

recommended that after installation

of the exhaust system you have all

slip connections tack welded by a

mufer shop.

NOTES:

1. All exhaust systems expand

about 1” rearward when exhaust

temperature rises.

3. Use anti-seize on threads of

clamps.

Other JBA 2010 Camaro Parts!

Emissions compatible shorty’s

Part No. Application

1812S 2010 6.2L stainless

1812SJS 2010 6.2L silver ceramic

1812SJT 2010 6.2L titanium ceramic

The Compete JBA 2010 Camaro

Competition system!

JBA Long Tube Headers

Part No. Application

6812S 2010 6.2L 1 3/4 stainless

6813S 2010 6.2L 1 7/8 stainless

JBA High Flow Mid-Pipes

Part No. Application

1812SY w/o Cats for 1812S

1812SYC w Cats for 1812S

6812SD

w/o Cats for 6812S

6812SDC

w/ Cats for 6812S

6813SD

w/o Cats for 6813S

6813SDC

w/ Cats for 6813S

15. With the system tightened and

installed to satisfaction, re-install

factory cross member.

16. Using a soft cloth, remove all

prints from exhaust tip.

5. Locate the keyways on the

band clamps attaching the factory

exhaust system to the cat pipe

assembly. Using a small at head

screw driver pry the tabs back to

release the factory exhaust system.

6. Your factory exhaust is a one

piece system and it is highly recom-

mended that a second individual

be employed to assist in removal.

While bracing the factory system,

use pliers remove all exhaust

hangers from the factory rubber

isolators.

7. With the system free from all

mounting points it can be com-

pletely removed from the vehicle in

one piece.

8. Slide the H-Pipe assemblies

into position. (Note: The 40-3114

reduces to 2.5” and will re-use the

factory band clamp. The 40-3113

must be used with JBA PN 6813SD

or 6813SDC and will use 2 supplied

Sure Seal™ clamps.)

4. Loosen the bolts on both factory

band clamps.

9. Slip the U-bolt clamp (H) over the

end of the H-pipe Align the H-pipe

assembly so that it is at and even

on both sides. Then tighten the U-

bolt clamp over the connection.

10. Install the intermediate pipes

(C & D) by slipping the ends into

the H-Pipe assembly. Make sure to

position all Sure Seal™ clamps (G)

as you build the system.

11. With the intermediate pipes in

place you are ready to hang the

mufer assemblies.

12. Hang the mufer assemblies

through the rear valence using the

factory rubber isolators.

13. Slip the Sure Seal™ clamps

(G) over the end of the mufer as-

semblies and nish hanging them

using the factory rubber isolators at

the center of the vehicle behind the

rear end.

14. Making sure that the tips are

centered and positioned well

through the rear valence, tighten

all clamps.

Inhaltsverzeichnis

Seite 1 - 40-3113 & 40-3114

HINSTALLATION INSTRUCTIONS** Installation recommendation: JBA recommends in most case that the vehicle be taken to a reputable exhaust shop for instal

Verwandte Modelle: JBA Exhaust 40-3113

Kommentare zu diesen Handbüchern

Keine Kommentare

Pertronix JBA Exhaust 40-3114 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Pertronix JBA Exhaust 40-3114 herunter. PerTronix JBA Exhaust 40-3114 User Manual [en] [de] Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: JBA Exhaust 40-3113

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Pertronix JBA Exhaust 40-3114