440 E. Arrow Highway, San Dimas, CA. 91773
909-599-5955 www.pertronix.com
LIMITED WARRANTY
Pertronix, Inc. Warrants to the original Purchaser of its solid-state ignition system (product) that the
Ignitor, magnet assembly and wiring (components) shall be free from defects in material and workmanship for a
period of (30) months from the date of purchase.
If within the period of the foregoing warranty Pertronix finds, after inspection, that the product or any
component thereof is defective, Pertronix will, at its option, repair such products or component or replace them
with identical or similar parts PROVIDED that within such period Purchaser:
1. Promptly Notifies Pertronix, in writing, of such defects.
2. Delivers the defective products product or component to Pertronix (ATTN: Warranty) with proof of purchase
date; and
3. Has installed and used the product in a normal and Proper manner, consistent with Pertronix printed
instructions.
THE FORGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESSED OR IMPLIED, INCLUDING AND IMPLIED WARRANTY OR MERCHANTABILITY OR
FITNESS FOR A PURPOSE.
THE FURNISHING OF A REPAIR OR REPLACEMENT COMPONENTS SHALL CONSTITUTE THE SOLE
REMEDY OF PURCHASER AND THE SOLE LIABILITY OF PerTronix WHETHER ON WARRANTY, CONTRACT
OR FOR NEGLIGENCE, AND IN NO EVENT WILL PerTronix BE LIABLE FOR MONEY DAMAGES WHETHER
DIRECT OR CONSEQUENTIAL.
12-VOLT NEGATIVE GROUND INSTRUCTIONS
GENERAL INFORMATION
1. See our website (www.pertronix.com) for the latest product information.
2. IMPORTANT: Read all instructions before starting installation.
3. WARNING!!! DO NOT USE WITH SOLID CORE IGNITION WIRES.
4.
The Ignitor II ignition can be used in conjunction with most ignition coils rated at 0.45 ohms or
greater.
5. All external resistors must be removed to achieve optimum performance from the Ignitor II ignition
system.
6. The Ignitor II is compatible as a trigger for most electronic boxes.
IGNITOR INSTALLATION
1. Remove the distributor cap and rotor. Do not disconnect spark plug wires. Examine cap
and rotor for wear or damage. Replace as needed.
2. Rotor tension spring must be removed from distributor shaft in order to remove dust
shield.
3. Disconnect the point wire from the negative (-) side of the coil. Remove the point wire,
point, and condenser.
4. The Ignitor does not require any modification to distributor. Therefore the point,
condenser and hardware can be used as backup.
5. Clean all dirt and excess oil from the breaker plate and point cam.
6. The Ignitor does not require any modification to distributor. Therefore the points,
condenser, and hardware can be used as backup.
7. Determine the rotation of your distributor rotor. The Ignitor can be installed in clockwise
or counter clockwise positions.
8. Install Ignitor plate using the screw hole stamped for the correct rotation. “C” indicates
the correct screw hole for clockwise rotation. “CC” indicates the correct screw hole for
counter clockwise rotation. Fasten the Ignitor plate to the distributor beginning with the
correctly stamped screw hole. Two screws must be used.
9. Install grommet into hole in the side of the distributor housing. The wire length inside
the distributor can be adjusted by gently pulling one wire at a time through the grommet.
CAUTION: care must be taken to insure wires do not interfere with moving parts.
10. Install magnet sleeve over distributor shaft, onto point cam Rotate sleeve until a slight
locating position is felt before applying pressure. With sleeve lined up on point cam, press
down firmly insuring sleeve is fully seated.
For Part Number: 91244A
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern