Pertronix JBA Exhaust 40-1666 Bedienungsanleitung PDF herunterladen

INSTALLATION INSTRUCTIONS

** Installation recommendation: JBA recommends in most case that the vehicle be taken to a reputable exhaust shop for installation.

JBA recommends taking the vehicle to a mufer shop and having all slip connections tack welded. 5.6.09

40-1665

08-09 Dodge Challenger SRT8 6.1L - 3 inch system

40-1666

2009 Dodge Challenger 5.7L - 2.5 inch system

Parts List Qty..

A. X-pipe 1

B. JBA mufer 2

C. Passenger side tail pipe with tip 1

D. Driver side tail pipe with tip 1

E. Sure Seal™ clamp 2

F. U-bolt clamp 6

G. Tip Adapter 2

Recommended Tools:

15mm deep socket

9/16 deep socket

13mm deep socket

Pry bar

WD-40 or equivalent

Start:

1. Remove and inventory new JBA

exhaust system.

2. Disconnect negative battery

cable and allow vehicle to cool.

3. With the vehicle raised and

properly supported, unbolt the fac-

tory cross member that runs under

the drive shaft and swing it out of

the way.

21. Tighten clamps, Tack weld slip

connections, and ball clamp, to

retain position of tip.

22. Using a soft cloth, remove all

prints from exhaust tip.

23. Check all clamps and con-

nections for proper t and align-

ment. Double check all clamps are

tightened and that all hangers are

secure in rubber grommets. It is

recommended that after installation

of the exhaust system you have all

slip connections tack welded by a

mufer shop.

NOTES:

1. All exhaust systems expand

about 1” rearward when exhaust

temperature rises.

3. Use anti-seize on threads of

clamps.

Other recommended products:

Get an extra 20+hp and faster ET’s

with a set of smog legal stainless

steel JBA Cat4ward® headers.

Part No. Application

1964S-1 05-06 5.7L stainless

1964S-1JS 05-06 5.7L silver ceramic

1964S-1JT 05-06 5.7L titanium ceramic

4. Using a pry bar, pry the exhaust

hangers from the factory rubber

isolators.

6. Unbolt the exhaust system from

the catalytic converter assemblies.

5. Unbolt the driver side rear mufer

/ tail pipe assembly and remove it.

7. Disconnect the ground strap

from the exhaust system and care-

fully remove the rest of the factory

exhaust system.

8. Slip the supplied Sure-Seal™

clamps (E) over the ends of the

catalytic converter assemblies.

9. Slip the new JBA X-pipe (A) over

the end of the catalytic converter

assembly.

10. Align the X-pipe (A) so that it is

at and even with the off-set exit on

the passenger side. Then tighten

the Sure-Seal™ clamps (E) over

the connection to the cat. assembly.

11. Slip the U-bolt clamps (F) over

the end of the X-pipe. Then install

the new JBA mufers (B) on to the

end of the X-pipe (A).

12. Align the mufers (B) so they

are at then tighten the U-bolt

clamps (F) over the connection.

13. Install the passenger side tail

pipe with tip (C) hangers into the

rubber isolators. Then slip the other

end onto the mufer (B).

15. Install the driver side tail pipe

with tip (C) hangers into the rubber

isolators. Then slip the other end

onto the mufer (B).

16. Install the supplied U-bolt

clamps (F) over the end of the muf-

ers (B).

17. Slip tailpipe tip adapters (G)

onto the end of the tailpipe. Con-

nect hangers.

18. Remove factory tips from

original exhaust. Remove original

clamps by carefully rolling off of the

stock ball connector, or you might

have to cut the attaching weld, if it

is too large to break loose.

19. Install stock tips onto the tip

adapters using the original clamp.

Adjust and align. If necessary, tip

adapter can be slid off of tailpipe

slightly to adjust length.

20. Check for adequate clearance

on frame, and body.

Inhaltsverzeichnis

Seite 1 - 40-1666

AINSTALLATION INSTRUCTIONS** Installation recommendation: JBA recommends in most case that the vehicle be taken to a reputable exhaust shop for instal

Verwandte Modelle: JBA Exhaust 40-1665

Kommentare zu diesen Handbüchern

Keine Kommentare

Pertronix JBA Exhaust 40-1666 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Pertronix JBA Exhaust 40-1666 herunter. PerTronix JBA Exhaust 40-1666 User Manual [de] Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: JBA Exhaust 40-1665

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Pertronix JBA Exhaust 40-1666