Pertronix Ignitor 2865 Bedienungsanleitung PDF herunterladen

12-Volt Negative Ground Installation Instructions

Page 1 of 4

CAUTION!!! Before installing, please read the following important information....

909-599-5955 www.pertronix.com

12-Volt Negative Ground Installation Instructions

Page 1 of 4

CAUTION!!! Before installing, please read the following important information....

909-599-5955 www.pertronix.com

1. The Ignitor is designed for 12-Volt negative ground systems.

2. Leaving the ignition “ON” with the engine “OFF” for an extended period could result in permanent damage to

the Ignitor.

3. See Chart on back page for coil recommendations.

4. Four & Six cylinder engines require a minimum of 3.0 ohms of primary resistance. Do not remove resistors if

the coil primary resistance is less than 3.0 ohms.

5. If your Ignition coil has the recommended primary resistance, remove or bypass all external resistors.

6. The Ignitor is compatible as a trigger for most electronic boxes.

12-Volt Negative Ground Installation Instructions

Page 1 of 4

For Part Numbers: 2865

DISASSEMBLY

1. PRIOR TO INSTALLATION TURN IGNITION SWITCH OFF OR DISCONNECT THE BATTERY

2. Remove the distributor cap, and rotor. Do not disconnect spark plug wires. Examine cap and rotor for wear

or damage. Replace as needed.

3. Disconnect the point wire from the negative (-) terminal of the coil.

4. Remove the point wire, condenser, both set of points and adapter plate from the distributor. The Ignitor does

not require any modification to the distributor. Therefore the point, condenser and hardware can be used as

backup.

5. Clean all dirt and excess oil from the breaker plate and point cam.

IGNITOR INSTALLATION

1. Position the Ignitor over point pivot pin and

eccentric adjustment screw, rotate eccentric screw as needed

to line up screw hole to breaker plate screw hole. Confirm that the Ignitor plate is flat and fits without

modifications. Fasten the plate into place using the original point screw.

2. Install magnet sleeve over the distributor shaft, onto point cam. Rotate the sleeve until a slight locating

position is felt before applying pressure. Press down firmly insuring sleeve is fully seated.

3. Module and magnet sleeve air gap is not adjustable.

4. Insert wires through the wire exit hole in distributor housing. Pull the rubber grommet into place. Make sure

wires do not interfere with any moving parts.

5. Reinstall the rotor, and the distributor cap. Make sure all spark plug wires are securely attached.

6. See Wiring Instructions.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - For Part Numbers: 2865

12-Volt Negative Ground Installation InstructionsPage 1 of 4CAUTION!!! Before installing, please read the following important information...909-599-5

Seite 2 - (FIGURE B)

COIL WIRERED WIREBLACK WIRETO IGNITION COIL WIRETO IGNITION SWITCHRED WIREBLACK WIRERESISTANCE WIREBALLAST RESISTORThe Ignitor can also be installed i

Seite 3 - POWER & GROUND TESTS

Q. What is the first thing I should check if the engine would not start? A. Make certain all wires are connected securely to the proper terminals.Q. T

Seite 4 - Page 4 of 4

LIMITED WARRANTY Pertronix, Inc. Warrants to the original Purchaser of its solid-state ignition system (product) that the Ignitor, magnet assembly an

Kommentare zu diesen Handbüchern

Keine Kommentare

Pertronix Ignitor 2865 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Pertronix Ignitor 2865 herunter. PerTronix Ignitor 2865 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Pertronix Ignitor 2865